We blast mold off wood, brick, and framing in hours, not days

Dry Ice Blasting Mold in VENTURA, California Without Water or Harsh Chemicals

Dry Ice Blasting Mold in VENTURA, California is a waterless remediation method that lifts mold from wood, brick, and framing without soaking your structure. If you have black mold growth on exposed beams or a crawl space that smells musty, we can help. Our team uses dry ice pellets at -109°F to clean surfaces in place, so you avoid tear-out and extra disposal fees. Call (833) 929-5837 for same-day dry ice mold remediation in VENTURA.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Dry Ice Blasting Mold by Mold Remediation Service Ventura
Careful work. Honest options.
About this service

What Dry Ice Blasting Mold in VENTURA, California Actually Does

Dry ice blasting mold uses compressed air to fire rice-sized dry ice pellets at mold-covered surfaces. The pellets hit at supersonic speed and sublimate on contact, going from solid to gas without a liquid phase. That thermal shock and kinetic energy lift mold, spores, and surface grime off wood, brick, concrete, and metal. Because no water is introduced, you avoid the moisture spike that can feed new growth. We pair the blasting with HEPA vacuum recovery and air scrubbing to capture what comes off.

Ventura sits in a coastal fog belt where morning humidity often sits above 70 percent. That moisture feeds black mold growth on attic sheathing, crawl space joists, and bathroom framing. Most of our calls come from homeowners near the beach or in older houses with poor ventilation. If you search for dry ice mold remediation near me VENTURA, you want a crew that understands how ocean air and marine layer cycles drive mold here. We do.

  • ✓ No Water, No Secondary Damage
  • ✓ Clean Wood and Brick in Hours
  • ✓ Less Tear-Out, Lower Disposal Cost
  • ✓ Kills Spores and Neutralizes Odors
What's included

What Our Dry Ice Blasting Mold Service Includes

Every dry ice blasting mold job includes inspection, containment, blasting, antimicrobial treatment, and clearance testing. We do not charge extra for HEPA vacuuming or air scrubbing. Here is what you get when you hire us.

✓

Full Mold Inspection

We use a moisture meter, thermal imaging camera, and boroscope inspection camera to find all mold growth. We check attics, crawl spaces, basements, and bathrooms. You get a written report with photos and a scope of work.

✓

Containment and HEPA Filtration

We seal the work area with plastic sheeting and zipper doors. A negative air machine with HEPA filters keeps spores from spreading. We run an air scrubber throughout the job. This protects your family and your belongings.

✓

Dry Ice Blasting

We use a dry ice blasting machine to remove mold from wood, brick, and concrete. The process uses no water and creates no chemical residue. We work in sections and HEPA vacuum as we go. Most jobs take 3 to 6 hours of blasting.

✓

Antimicrobial Treatment

After blasting, we apply an antimicrobial spray like Sporicidin or Microban. For tight spaces, we use a fogging machine. This step stops remaining spores from regrowing. The treatment dries in about 2 hours.

✓

Post-Remediation Testing

We collect air samples with an air sampling pump and send them to a third-party lab. You get the results in writing. If clearance fails, we re-clean at no charge. This is how we prove the job is done right.

How it works

Our Dry Ice Blasting Mold Process

01

Inspection and Testing

We start with a boroscope inspection camera to see inside walls and crawl spaces. A moisture meter and thermal imaging camera map the extent of water damage mold. We collect air samples with an air sampling pump and send them to a lab. You get a written report with spore counts and a clear scope of work within 24 hours.

02

Containment Setup

We seal the work area with plastic sheeting and zipper doors. A negative air machine with HEPA filters keeps spores from spreading to clean rooms. Our technicians wear Tyvek suits and respirators. We set up an air scrubber to run continuously during the job. Setup takes 30 to 60 minutes depending on the size of the space.

03

Dry Ice Blasting

We use a dry ice blasting machine to fire pellets at 150 to 300 PSI. The pellets sublimate on impact and lift mold off wood, brick, and concrete. A second technician follows with a HEPA vacuum to capture debris. We work in 4-foot sections and check progress with a moisture meter. Most residential jobs take 3 to 6 hours of blasting time.

04

Antimicrobial Treatment

After blasting, we apply an antimicrobial spray like Sporicidin or Microban to the cleaned surfaces. For crawl spaces and attics, we use a fogging machine to reach tight corners. We treat all wood framing, joists, and subfloor. This step stops any remaining spores from regrowing. The treatment dries in about 2 hours.

05

Verification and Clearance

We run a final air sampling pump test to confirm spore levels are back to normal. A third-party lab analyzes the samples, and we share the results with you. If levels are still high, we re-blast at no extra charge. We also provide a written warranty and maintenance tips. Most jobs pass clearance on the first test.

Tools & methods

Tools and Methods for Dry Ice Blasting Mold

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Dry Ice Blasting Machine

Fires rice-sized dry ice pellets at supersonic speed to remove mold from wood, brick, and concrete without water or chemicals.

HEPA Vacuum

Captures mold spores and debris released during blasting. We use HEPA filters rated for 99.97 percent of particles at 0.3 microns.

Negative Air Machine

Creates negative pressure in the containment area so spores cannot escape into clean rooms. We use Abatement Technologies units.

Air Scrubber

Runs continuously during the job to filter airborne particles. We use Dri-Eaz and Phoenix Restoration Equipment scrubbers.

Moisture Meter

Measures moisture content in wood and drywall. We use it to find hidden water damage mold and to confirm materials are dry.

Thermal Imaging Camera

Detects temperature differences that indicate moisture behind walls. Helps us locate mold without tearing out materials.

Boroscope Inspection Camera

Allows us to see inside wall cavities and crawl spaces without major demolition. We use it to confirm mold growth in hidden areas.

Real results

Before and after.

Attic Mold Removal in Midtown Ventura

Before

A homeowner found black mold on attic sheathing after a roof leak. Spore counts were 4 times normal. The attic had no ventilation, and humidity was trapped.

After

We blasted the sheathing and rafters with dry ice, HEPA vacuumed, and applied Sporicidin. Post-remediation testing showed normal spore levels. The job took 5 hours.

Crawl Space Mold Remediation in Ventura Keys

Before

A crawl space had mold on 60 percent of the joists. The musty odor was noticeable in the living room. Moisture readings were above 20 percent.

After

We blasted the joists and subfloor, treated with Concrobium, and installed a vapor barrier. Moisture dropped to 12 percent. The odor was gone within 24 hours.

Bathroom Mold Removal in Pierpont Bay

Before

Mold grew behind the shower tile from a slow leak. The drywall and framing were affected. The bathroom fan was undersized.

After

We removed the tile, blasted the framing, and treated with Benefect. We installed a new exhaust fan. Clearance testing passed on the first try.

Problems we solve

Problems We Solve with Dry Ice Blasting Mold Removal

Mold in Ventura comes from ocean humidity, roof leaks, and plumbing failures. Dry ice blasting solves the problem without adding moisture. Here are the most common issues we fix.

Ask a pro →
01

Black mold growth on attic rafters

We contain the attic, blast the rafters with dry ice, and HEPA vacuum all surfaces. Then we apply antimicrobial spray and verify with air testing. Most attics are clean in one day.

↗
02

Crawl space mold from high humidity

We blast the joists and subfloor without adding water. We also check for plumbing leaks and poor drainage. If needed, we install a vapor barrier to prevent future growth.

↗
03

Bathroom mold behind tile and drywall

We open the wall, blast the framing with dry ice, and treat with Benefect. We also fix ventilation issues that cause bathroom mold. The wall is closed after clearance testing.

↗
04

Water damage mold after a pipe burst

We extract water, dry the structure, then use dry ice blasting to clean affected wood and drywall. We work fast to prevent further growth. Emergency response is available.

↗
Proof you can check

Licensed, Certified, and Insured

✓
IICRC AMRT (Applied Microbial Remediation Technician)Institute of Inspection, Cleaning and Restoration Certification
✓
IICRC WRT (Water Restoration Technician)Institute of Inspection, Cleaning and Restoration Certification
✓
ACAC CMI (Certified Mold Inspector)American Council for Accredited Certification
✓
ACAC CMR (Certified Mold Remediator)American Council for Accredited Certification
✓
EPA Lead-Safe CertificationU.S. Environmental Protection Agency
Good questions

Frequently Asked Questions About Dry Ice Blasting Mold

(833) 929-5837 →

Most dry ice blasting mold removal VENTURA California cost falls between $1,800 and $4,500 for a typical attic or crawl space. Small bathroom jobs can run $900 to $1,500. Large commercial spaces or severe black mold growth may reach $7,000 or more. The price includes inspection, containment, blasting, antimicrobial treatment, and clearance testing. We give you a written quote before we start.

Dry ice blasting mold remediation in VENTURA is a cleaning method that uses compressed air and dry ice pellets to remove mold from wood, brick, and concrete. The pellets hit at supersonic speed and sublimate on contact, lifting mold without water or chemicals. It is faster than sanding and creates less mess than media blasting. We follow with HEPA vacuuming and antimicrobial spray to complete the remediation.

Yes. Dry ice blasting is safe for most building materials when done by trained technicians. The process uses no water, so it will not warp wood or feed new mold growth. We use negative air machines and HEPA filters to keep spores out of your living space. Our crew wears Tyvek suits and respirators. We also test air quality after the job to confirm it is safe to reoccupy.

Mold Remediation Service Ventura offers dry ice mold remediation in VENTURA and across Ventura County. We have been in business since 2022 and hold IICRC AMRT, WRT, ACAC CMI, and CMR certifications. We serve Downtown Ventura, Midtown, Pierpont Bay, Ventura Keys, East Ventura, Montalvo, and surrounding areas. Call (833) 929-5837 to schedule an inspection or request a quote.

Ready when you are

Schedule Your Dry Ice Blasting Mold in VENTURA, California Today

We are licensed, insured, and certified for mold remediation in Ventura. Call (833) 929-5837 for a same-day inspection or to schedule dry ice blasting. We give you a written price before we start. Most jobs are completed in one day.

Get a Free Quote (833) 929-5837 →
Request an appointment

Contact Mold Remediation Service Ventura

Call us at (833) 929-5837 any time, day or night. Our phone line is answered by a real person, and we can usually schedule an inspection within 24 hours. For emergencies like burst pipes or post-flood mold, we can be on-site in Ventura within a few hours. You can also email us at info@moldremediationserviceventura.com.

Request received — our team will be in touch shortly.
Tap to call(833) 929-5837